Linksys SPA3000的功能与设置技巧

SPA3000的功能特点：
Telephony
• VoIP to PSTN (USA) Service Call Origination and Termination
• PSTN (USA) to VoIP Service Call Origination and Termination
• Single or Dual Stage Dialing
• Service Authentication via PIN, Digest, Caller ID (Bellcore Type 1)
• Per Call Authentication and Associated Routing
• Least Cost Routing Support
• Impedance Agnostics - 8 Settings
• Call Waiting, Cancel Call Waiting, Call Waiting Caller ID Detection (Bellcore Type 1)
• Caller ID with Name/Number (Multi-national Variants)
• Caller ID Blocking
• Call Forwarding to PSTN or VoIP Service: No answer, Busy, All
• Do Not Disturb
• Call Transfer
• Three-way Conference Calling with Local Mixing
• Message Waiting Indication - Visual and Tone Based
• Call Return
• Call Back on Busy
• Call Blocking with Toll Restriction
• Delayed Disconnect
• Distinctive Ringing - Calling and Called Number
• Off-hook Warning Tone
• Selective/Anonymous Call Rejection
• Hot line and Warm Line Calling
• Speed Dialing of 8 Numbers/Addresses
• Music on Hold
SPA3000 Specific
• Forward Calls to VoIP service - Selective, Authenticated, All
• Forward Calls to PSTN service - Selective, Authenticated, All
• PSTN Line Sharing with Multiple Extensions
• Automatic PSTN Fallback (Loss of Power or IP Service to Unit - with Quiescence to Normal Operations)
• Advanced Inbound and Outbound Call Routing
• Single Stage and Two Stage Dialing
• Independent Configurable Dial Plans - Up to 8
• Force PSTN Disconnection
• Sequential Dialing Support
VoIP to PSTN Authentication and Routing
• VoIP to PSTN Gateway Enable/Disable
• VoIP Caller Auth Method (None, PIN, HTTP Digest)
• VoIP PIN Max Retry Setting
• One Stage Dialing Enable/Disable
• VoIP Caller ID Pattern Matching
• VoIP Access Allowed Caller List (No Further Authentication)
• VoIP Caller PIN and Associated Dial Plan
PSTN to VoIP Authentication and Features
• PSTN to VoIP Gateway Enable/Disable
• Caller Auth Method: None, PIN, Caller ID
• Ring Through to FXS Enable/Disable
• Ring Through Tone - Configurable
• Caller ID (Bellcore 1) for VoIP Service Access
• Caller ID Enable/Disable
• PIN Max Retry Settings
• Access Allowed Caller List (No Further Authentication)
• Caller PIN and Associated Dial Plan
• Least Cost Routing (via Outbound VoIP - Line1 Dial Plan)
FXO Behavior
• VoIP Answer Delay Timer
• PSTN Answer Delay Timer
• VoIP PIN Digit Time-Out Timer
• PSTN PIN Digit Time-Out Timer
• PSTN-to-VoIP Call Max Dur Timer
• VoIP-to PSTN Call Max Dur Timer
• PSTN Ring Through Delay Timer
• PSTN Dialing Delay Timer
• VoIP DIG Refresh Interval Timer
• PSTN Ring Time-out Timer
PSTN Disconnection Detection
• CPC (Removal of Tip/Ring Voltage Momentarily)
• Polarity Reversal
• Long Silence (Confugrable Time Setting)
• Disconnect Tone (e.g. Reorder Tone)
International Control
• FXO Port Impedance - Configurable to 16 settings
• Ring Frequency - Configurable
• SPA to PSTN and PSTN to SPA Gain Settings
• Ring Frequency - Maximum Setting
• Ring Validation Time Setting
• Tip/Ring Voltage Adjustment Setting
• Ring Indication Delay Setting
• Operational Loop Current Minimum Value
• Ring Time-out Setting
• On-Hook Speed Setting
• Ringer Impedance Setting
• Line-in-Use Voltage Setting
• FCC (Part 15 Class B and Part 68) , CE , ICES-003
• Password Protected System Reset to Factory Default
• Password Protected Admin and User Access Authority
• Provisioning/Configuration/Authentication:
• HTTP Digest - Encrypted Authentication via MD5 (RFC 1321)
• Up to 256-bit AES Encryption
• Quick-Start Installation and Configuration Guide
• User Guide
• Administration Guide - Service Providers Only
• Provisioning Guide - Service Providers Only
• 1 - SPA3000 Phone Adapter Unit
• 1 - 5v Power Adapter
• 1 - RJ45 Ethernet Cable
• 1 - RJ11 Telephone Cable
Dimensions
Unit Weight
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
4.05 x 1.1. x 3.75 in (102.87 x 27.94 x 95.25 mm) W x H x D
2.15 lb (0.975 kg)
32º~113ºF (0º~45ºC)
-13º~185ºF (-25º~85ºC)
10~90% Non-condensing
10~90% Non-condensing

SPA3000的设置：
1：在电话机上按“*”键四次，再按110#，即可听到电话机报出来的IP地址。在和路由器相连的电脑上，用IE浏览器输入这个IP地址，即可进入设置页面。

2：点击左上角的“admin log in”，选择Line1，即可进入以下界面：



按如上图示分别填入相应的配置。点击最下面的“Save Changes”即可。

3：由于此款网关最大的优势是既可以利用现有的电话来拨打固定电话，又可以拨打网络电话，那么我们需要在固定电话和网络电话之间设定切换键。 首先需要点击左上角的“advance”进入高级配置界面，然后再点击 “line 1”



在Line1里面的Dial Plan里面填入你的拨号方式。由于拨号方式的设置可以有很多形式，从而功能也就不一样。笔者只是简单的设置在固定电话和网络电话之间切换键：

(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.|<#9:>xx.<:@gw0>)

通过填上以上设置，当我们拿起电话直接拨打数字代表是通过网络电话线拨打，当我们先拨打#9，就会切换到普通电话线，你就可以像平常一样拨打电话了。

4， 转接设置
SPA3000提供的是真FXO口，它除了逃生口的功能外还具有转接功能，即可以实现VoIP网络和PSTN网络的互转。通过此功能可实现手机拨打网络电话的功能。比如你现在在外面，但是想用手机走VoIP网络拨打一个国际长途或者国内长途，这时你可以拨打你家里SPA3000所连接的PSTN号码（比如0755 *********），然后再听到二次拨号音后再输入想要拨打的国际长途号码，就实现了用手机拨打VoIP电话的功能。

具体设置如下：
（1） 进入 “admin log in”----“advance”，点击“PSTN line”。
（2） 需要配置好一个VOIP账号，配置方法和上面说的“Line1”配置一样，但是最好是另外一个账号。配置完之后就可以实现。 配置好VoIP账号之后，就可以实现VoIP网络和PSTN网络互转了。
（3） 当你拨打PSTN line里配置的VoIP号码并接通之后会马上听到第二次拨号音（中间没有间隔时间，因为默认的配置间隔时间是0，并没有设置密码），此时输入想要拨打的号码，实际上就是在使用原来的普通PSNT线路在打电话了。
（4） 当你拨打PSTN线路的号码并接通之后，连接在FXS口上的电话机会响铃，过上一段时间（默认配置是间隔16s）如果没有人接听，就会听到第二次拨号音，此时输入想要拨打的号码并以“#”结束，实际上就是在使用PSTN line里配置的VoIP账号在打电话了。这也就可以实现用手机拨打VOIP电话。